PRODUCT DATASHEET · HOMALL · TELESCOPIC MAST SYSTEMS
MES-4-58 · MANUAL TELESCOPIC MAST · HOMALL
MANUAL MECHANICAL
Telescopic Mast
MES-4-58
A four-section square-tube telescopic mast on a spindle drive: it locks at any height the operator chooses, carries 50 kg, and reaches 5.8 m from a 1.8 m retracted length. HOMALL builds the mast in heat-treated 6063 aluminium with stainless steel fasteners and the cable running inside the tube — the manual telescopic mast specified for trailer, outdoor security, firefighting, outdoor lighting and mobile security-box builds.
|
5.8 m Extended height |
1.8 m Retracted height |
4 Sections |
50 kg Payload |
|
From 2025 the mast has gone through a major upgrade. The square-tube manual mechanical system has been switched to spindle drive, to give more stability and to lock at any height you choose. All mast components are high-tensile aluminium — copper nut, stainless steel screw — and the cable runs inside the tube, so nothing corrodes and nothing snags. That makes the mast suited to trailer, outdoor security, firefighting, outdoor lighting, and mobile lighting and security box applications. |
|
Shown retracted. Yellow powder coat, stainless fasteners, cast base.
|
|
“Going up by rope, going down by rope too — so the mast never gets stuck.” Dual-way stainless steel rope, built inside the mast |
01 WHAT CHANGED FOR 2025: SPINDLE DRIVE
Spindle drive, not rope and pulley. The elevation mechanism was rebuilt around a spindle. It holds the telescopic mast at whatever height the operator stops at, and it keeps the four square sections aligned as they travel — the source of the stability gain over a rope-and-pulley mast.
Dual-way rope inside the mast. Most manual masts on the market run one-way rope: up on the rope, down on gravity and a brake. The HOMALL mast runs rope both ways, so the telescopic mast lowers under control in any weather and never sticks at height.
Figure 1 Cut-away of the mast body: the spindle runs the full length of the section, carried on the gear and bearing set at the base. Crank winch sits on the outer section.
02 TECHNICAL SPECIFICATION
|
Extended height 5.8 m |
Retracted height 1.8 m |
|
Number of sections 4 |
Tube diameter range 70 – 124 mm |
|
Payload capacity 50 kg |
Material 6063 aluminium, heat treated against corrosion |
|
Model |
MES-4-58 |
|
Brand |
HOMALL |
|
Mast type |
Manual mechanical telescopic mast — square tube, spindle drive |
|
Finish |
Yellow powder coat, stainless steel fasteners, cast base |
|
Winch |
IP67 crank winch with cable sink |
|
Rope |
Dual-way stainless steel rope, carried inside the tube |
|
Mounting plate |
200 mm square, 4 × Ø12 holes on a 175 mm pattern |
|
Crank and boss |
Crank centre at 900 mm; boss drilled 4 × M8 × 22 mm deep |
03 KEY FEATURES OF THE MES-4-58
|
01 All mast components in high-tensile aluminium Copper nut and stainless steel screw throughout, so the mast holds up in coastal, wet and high-humidity service. |
|
02 Spindle driven, lockable anywhere Lockable at any height the operator chooses, with the stability of a screw thread rather than a brake. |
|
|
|
|
|
03 Cable carried inside the mast All mast cable is built inside the tube, so it withstands weather and cannot snag on the way up. |
|
04 IP67 winch with cable sink A customised winch and cable sink protect the cable from abrasion — protection commodity winches do not give you. |
|
|
|
|
|
05 Elevation and stop at any height No preset positions and no pin holes: the operator sets the working height for the job. |
|
06 Structurally upgraded Lighter than a galvanised iron mast, with the stiffness of a heat-treated 6063 square section. |
|
|
|
|
|
07 Dual-way stainless steel rope kit — up by rope, down by rope |
04 WHERE THIS TELESCOPIC MAST IS USED
|
Trailer Vehicle-mounted lighting and surveillance |
Outdoor security Perimeter and site surveillance |
Firefighting Scene lighting and monitoring |
Outdoor lighting Temporary and permanent floodlighting |
Security box Mobile lighting and security builds |
A 50 kg payload and a 1.8 m retracted length make the MES-4-58 a direct fit for vehicle-mounted lighting and surveillance masts, perimeter security trailers, firefighting scene lighting, temporary and permanent floodlighting, and mobile security-box builds. Elevation is by crank winch and the mast locks on a spindle, so no hydraulic power pack or compressor has to travel with the mast.
05 DIMENSIONAL DRAWING
Figure 2 General arrangement and mounting interface. Front and side elevation, section A–B through the tube (□124 outer, □64 inner), and the mounting plate: 200 mm square, four Ø12 holes on a 175 mm pattern. Crank centre at 900 mm, boss drilled 4 × M8 × 22 deep.
06 BUILT IN-HOUSE
HOMALL builds the MES-4-58 in-house, from tube to crate, which is why the spindle, the winch and the cable sink are made for this mast rather than bought in as commodity parts.
|
6063 tube stock, cut to section length. |
Section assembly and bench fitting. |
Finished masts crated for shipment. |
· HOMALL · Manual mechanical telescopic mast systems · MES-4-58
07 HOW TO SPECIFY: HEIGHT, PAYLOAD, MOUNTING
Choosing a manual telescopic mast comes down to three numbers and one interface. This is how the MES-4-58 is specified, in the order a mast is usually bought.
Working height and retracted length. The MES-4-58 gives 5.8 m of extended height from 1.8 m retracted, across four square sections in a 70 – 124 mm tube range. Measure the height you need at the payload, not the height of the mast box: the mast lifts a lighting or camera head to just under six metres, and still stows inside a 1.8 m envelope on the vehicle or trailer.
Payload and head load. Rated payload is 50 kg, which covers a pan-and-tilt camera head, a floodlight bar, a scene light or an antenna cluster. Keep the mass at the top of the mast low and centred: the spindle holds the working height, while the square sections carry the bending moment.
Mounting interface. The cast base takes a 200 mm square mounting plate with four Ø12 holes on a 175 mm pattern; the crank centre sits at 900 mm and the boss is drilled 4 × M8 × 22 mm deep. That plate is what the trailer bed, roof rack or security box is designed around, so agree it before anything else.
Manual drive, no power at the mast. Elevation is by crank winch, with an IP67 winch body and a cable sink protecting the rope from abrasion. Up and down both run on dual-way stainless steel rope inside the tube, so the mast lowers under control instead of dropping on a brake — and no hydraulic pack, compressor or electrical supply is needed where the mast is mounted.
Finish and service life. Tubes, nut and screw are high-tensile aluminium with a copper nut and stainless steel screw, finished in yellow powder coat with stainless fasteners on a cast base. In coastal, wet or high-humidity sites, that combination is what keeps the sections sliding after years of use.
08 FREQUENTLY ASKED QUESTIONS
What is a manual telescopic mast?
A mast raised and lowered by hand — here by crank winch — rather than by hydraulics, pneumatics or an electric actuator. The MES-4-58 is a four-section square-tube manual telescopic mast that locks wherever the operator stops turning, so nothing has to be powered at the mast head.
How high does the MES-4-58 extend, and what does it carry?
5.8 m extended and 1.8 m retracted, with a rated payload of 50 kg. Four sections travel in a 70 – 124 mm square tube range, in heat-treated 6063 aluminium.
How does the mast lock at any height?
On a spindle. The spindle runs the full length of the section, carried on the gear and bearing set at the base, so the mast holds at whatever height the operator stops at — no preset positions, no pin holes, and no brake to slip under load.
Can it be mounted on a trailer or a vehicle?
Yes. Trailers, vehicle-mounted lighting and surveillance, outdoor security, firefighting scene lighting, temporary and permanent floodlighting and mobile security-box builds are the applications this telescopic mast is specified for. The mounting plate is 200 mm square with four Ø12 holes on a 175 mm pattern.
Will the mast corrode, and what happens to the cable?
The mast is high-tensile aluminium with a copper nut, stainless steel screw, stainless fasteners and a cast base, finished in powder coat. All mast cable runs inside the tube, so it stays out of the weather and cannot snag as the sections travel.
Is the mast driven by rope in both directions?
Yes — dual-way stainless steel rope, running inside the mast. Most manual masts go up on the rope and come down on gravity and a brake; the HOMALL mast is driven by rope both ways, so it lowers under control and never sticks at height.
Who builds the mast?
HOMALL. Tube stock is cut to section length, sections are assembled and bench-fitted, and finished masts are crated for shipment — all in-house, which is why the spindle, winch and cable sink are made for this mast rather than bought in as commodity parts.
09 ORDER THE MES-4-58 FROM HOMALL
HOMALL supplies the MES-4-58 as a complete manual telescopic mast: four square tube sections, spindle drive, IP67 crank winch, dual-way stainless steel rope and cast base. Send the payload, the mounting plate you need and the finish, and we confirm the configuration before the mast is built. General-arrangement drawings for the MES-4-58 are available on request.
HOMALL · MANUAL MECHANICAL TELESCOPIC MAST SYSTEMS · MES-4-58
10 PUBLISHING DATA FOR THE WEB TEAM
Internal page. Delete this section before printing the datasheet.
|
Page URL |
/products/manual-telescopic-mast-mes-4-58/ |
|
SEO title (52 characters) |
Manual Telescopic Mast MES-4-58 | 5.8 m, 50 kg | HOMALL |
|
Meta description (151 characters) |
HOMALL MES-4-58 manual telescopic mast: four square sections, spindle drive that locks at any height, 5.8 m extended, 50 kg payload, 6063 aluminium. |
|
H1 on the page |
Manual Telescopic Mast MES-4-58: 5.8 m, 50 kg, Spindle Drive |
|
Primary keyword |
manual telescopic mast |
|
Secondary keywords |
4-section telescopic mast · aluminium telescopic mast · spindle drive telescopic mast · 5.8 m telescopic mast · 50 kg payload mast · vehicle mounted telescopic mast · mobile lighting mast · firefighting lighting mast |
|
Image file names |
homall-mes-4-58-manual-telescopic-mast.jpg · homall-mes-4-58-spindle-drive-cutaway.jpg · homall-mes-4-58-dimensional-drawing.jpg |
|
Image alt text |
1) HOMALL MES-4-58 manual telescopic mast, four-section square tube, retracted on a cast base. 2) Cut-away of the MES-4-58 mast body showing the spindle drive and the cable route inside the tube. 3) MES-4-58 telescopic mast general arrangement: 200 mm square mounting plate, 4 Ø12 holes on a 175 mm pattern. |
|
Structured data |
Product (name, brand HOMALL, model MES-4-58, material, height, payload, image) + BreadcrumbList + FAQPage for the seven questions in section 08. Do not mark up a rating or a price unless one is published. |
|
Internal links |
Telescopic mast category page · trailer mast application page · security and surveillance mast page · firefighting lighting mast page. Use descriptive anchor text, never "click here". |
|
Canonical |
Self-referencing to the page URL above. One URL only — no /products/ and /products.html duplicates. |
-
Copyright © 2026 Homall Industry Limited All rights reserved. Sitemap RSS XML Privacy Policy